Recent content by cygan

C
Two Gateways

@kevnich2: Thanx a lot. I tried adding a static route on the server 2 (the SAP Server), and it worked. And to be honest, it wasn't working that way yesterday. However, i am a little scared because there is so much of experimentation done, I am in fact not sure which one worked. In fact I am...
- cygan
- Post #14
- Jun 24, 2013
- Forum: Networking
C
Two Gateways

@kevnich2: Oops, I missed out on that one. PC3 & PC4 have a default gateway of 192.168.16.1. I have corrected the diagram too. My basic requirement now is that PC3 & PC4 communicate with Server 1 & 2, i.e from PC3& PC4 to Server 1 & @. Server 1 & 2 can communicate with PC3 & PC4 after static...
- cygan
- Post #11
- Jun 24, 2013
- Forum: Networking
C
Two Gateways

I tried adding the following on server1: route add 192.168.16.0 mask 255.255.255.0 192.168.0.1 I can then direct traffic or ping from the server to the 192.168.16.0 network. But the reverse does not work i.e I dont get a response from either server when I ping from the 192.168.16.x network...
- cygan
- Post #9
- Jun 23, 2013
- Forum: Networking
C
Two Gateways

@drebo: the whole network was built in piecemeals. I know that the network is not optically configured, but at present I cannot change anything. Is there any way I can direct traffic coming from the 192.168.16.x segment to the server2 at 192.168.0.242/ 192.168.1.242. Is there any way I can...
- cygan
- Post #7
- Jun 23, 2013
- Forum: Networking
C
Two Gateways

@Lemieux66: Would that mean I will have to remove the existing gateway of 192.168.1.1 on NIC2,and then put 192.168.0.1 on NIC1 because it says multiple gateways will not function properly when gateways are on two separate disjoint networks? One more thing is that though 2 locations are shown...
- cygan
- Post #5
- Jun 23, 2013
- Forum: Networking
C
Two Gateways

Maybe this diagram will explain my situation better. http://www.cyberganesha.com/downloads/LAN.jpg I want PC3 & PC4 to access servers 1 &2. (at least server2) With the present ip, PC2 can access PC3 & PC4. PC1 & the Servers cannot access PC3 & 4 till a static route is added. PC3 &...
- cygan
- Post #2
- Jun 23, 2013
- Forum: Networking
C
Two Gateways

I am stuck in a networking soup. My client has recently got MPLS installed for connecting his two offices. He has asked me to connect the two networks, so that the server is accessibe from the spoke location. I shall first describe the two networks (Hub & Spoke). The Hub location has two...
- cygan
- Thread
- Jun 21, 2013
- Replies: 13
- Forum: Networking
C
VPN Trouble

Thank you Spidey * RM for all your help. I changed the Ip range at the workplace to 192.168.16.x and it worked. Thank you for all your help
- cygan
- Post #8
- Jul 14, 2009
- Forum: Networking
C
Bad NIC? UPDATE!!!

I have faced these unusual problems with Dell laptops, the Vostro A840. Suddenly the network connections disappear, and you don't find a NIC in the Device Manager. However, you format the machine, and load the drivers, the NIC appears, but does the disappearing act again after a short while. All...
- cygan
- Post #9
- Jul 10, 2009
- Forum: Networking
C
VPN Trouble

Like you said, the client computer must not be passing the requests through the tunnel. have changed the IP range of the workplace to 192.168.16.x. I wanted to try the VPN thing today, but couldn't. I shall try to try the VPN tomorrow morning and let you know. Hope that works. Thanx a lot...
- cygan
- Post #6
- Jul 10, 2009
- Forum: Networking
C
VPN Trouble

One more thing I wanted to inform you was that when I observed the packets on my home pc after connecting through VPN was that packets were only sent, but not received.The rceeived packets figure remained stationary all through out. Thanx
- cygan
- Post #4
- Jul 9, 2009
- Forum: Networking
C
VPN Trouble

Dear Spidey, Do all routers have that facility, because I can't find any section to forward protocols. However I have set the source protocol to PPTP, before which even the connection wasn't going through Thanx
- cygan
- Post #3
- Jul 9, 2009
- Forum: Networking
C
VPN Trouble

I have problem viewing or pinging my client's workplace PC's over VPN. At my client's workplace I have an SBS 2003 Server Standard Edition, which has been configured for RRAS and VPN. The server has a single NIC -configured to an IP of 192.168.1.105 with a subnet 255.255.255.0. The internet...
- cygan
- Thread
- Jul 9, 2009
- Replies: 8
- Forum: Networking
C
Internet connectivity over a switch

Pls. let me clarify.there are three offices over 3 floors. Each office is networked by a single switch on that floor. Only offices on the uppermost floor use the services of a win 2k3 server that is situated on that floor and connected to the switch on that floor.The router too is connected to a...
- cygan
- Post #9
- Apr 14, 2008
- Forum: Networking
C
Internet connectivity over a switch

The network seems to be working ok. It also has a windows 2003 server, which I did not mention. The network does not use file sharing to a large extent, but uses software off the server, for which the P2P network seems to be doing fine. I tried using a single lan card for internet connectivity...
- cygan
- Post #6
- Apr 13, 2008
- Forum: Networking

RESOURCES

Top Bottom