Recent content by DaPoets

D
Question RGB Fans not lighting up

Have you tried plugging in each fan individually just to make sure they actually work first?
- DaPoets
- Post #2
- Dec 11, 2019
- Forum: Cases & Cooling
D
Benchmark your computer @4K with Handbrake 1.1 and H265! NOW WITH ZEN3!

encoded 1806 frames in 123.66s (14.60 fps), 11820.04 kb/s, Avg QP:29.09 Threadripper 3960X stock settings. 64GB DDR4 3600Mhz 16-19-19-39-1T
- DaPoets
- Post #111
- Dec 11, 2019
- Forum: CPUs and Overclocking
D
would X1950 Pro run on this cheap PSU?

19a needed boys and girls...
- DaPoets
- Post #4
- Oct 8, 2007
- Forum: Graphics Cards
D
Benifits of 512mb ram over 256mb

Come big or go home.
- DaPoets
- Post #14
- Oct 8, 2007
- Forum: Graphics Cards
D
Crossfire x1950Pro 512MB What's your PSU???

hmm I'll look into that. I did find out though that my Antec Trio is actually right on the mark. Crossfire requirments adds the total amps needed, so that's two 12v rails w/ 19amps each... equating to 38amps which is what my Antec gives so I'm actually ok... but if I upgrade in the future, who...
- DaPoets
- Post #3
- Oct 7, 2007
- Forum: Graphics Cards
D
Crossfire x1950Pro 512MB What's your PSU???

My Antec Trio 650 isn't giving enough amps per 12v rail (only 19a) to my Crossfire setup which requires 38amps per 12v rail... For those of you using x1950pro's w/ 512megs, what PSU are you using?
- DaPoets
- Thread
- Oct 6, 2007
- Replies: 2
- Forum: Graphics Cards
D
Q6600 B3 D975XBX2 need help getting past 3.2 ghz on air

I decided to try w/ EIST off on my current bios settings to try to keep the Vdrop from happening... anyone else have this off?
- DaPoets
- Post #13
- Sep 13, 2007
- Forum: CPUs and Overclocking
D
Q6600 B3 D975XBX2 need help getting past 3.2 ghz on air

There is a new bios 2792 for my board, I'm going to try it out.... if it doesn't work I'll try the 2203 if I can find it.
- DaPoets
- Post #11
- Sep 12, 2007
- Forum: CPUs and Overclocking
D
Q6600 B3 D975XBX2 need help getting past 3.2 ghz on air

My temps are not going above 61°c though....
- DaPoets
- Post #9
- Sep 12, 2007
- Forum: CPUs and Overclocking
D
Q6600 B3 D975XBX2 need help getting past 3.2 ghz on air

So I tried 3.3ghz at 1.55v, 1.5v fsb, 1.55v MCH/ICH and I would get a Prime95 error w/ in 1 min...
- DaPoets
- Post #7
- Sep 12, 2007
- Forum: CPUs and Overclocking
D
Q6600 B3 D975XBX2 need help getting past 3.2 ghz on air

For intel board you can not lower the multiplyer and for Intel boards what is the equivlent for VNB... the FSB voltage or the MCH/ICH....
- DaPoets
- Post #5
- Sep 12, 2007
- Forum: CPUs and Overclocking
D
Q6600 B3 D975XBX2 need help getting past 3.2 ghz on air

as you see I have a B3 so that's apples/oranges... I have seen the BX2 q6600 B3 get past 3.4ghz on water... I'm just trying to get past 3.2ghz...
- DaPoets
- Post #3
- Sep 12, 2007
- Forum: CPUs and Overclocking
D
Q6600 B3 D975XBX2 need help getting past 3.2 ghz on air

Q6600 B3 D975XBX2 need help getting past 3.2 ghz on air Currently I am running at full load at 3.2ghz at the following temps: 57°c 55°c 57°c 52°c Current settings in Bios on my Intel D975xbx2: ram 266/533 2.2v (pc 6400) 4-4-4-12 (same issues if at 5....) 1.2875v core 1.3v FSB 1.55...
- DaPoets
- Thread
- Sep 12, 2007
- Replies: 13
- Forum: CPUs and Overclocking
D
Is this lapping job adequate?

My house is brick and I had all the lights on in my office, windows open but there was no breeze last night, so I would say it was about 82 F. My house just stays warm unless I put on the Central Air. My house thermostat said 86 F last night but it didn't seem that warm so I'm knocking it down...
- DaPoets
- Post #29
- Sep 5, 2007
- Forum: Cases & Cooling
D
Is this lapping job adequate?

I ended up lapping both my Q6600 and my Thermalright Ultra 120 Extreme tonight... yeah I'm tired... It took me about 3.5 hours total and I went through 220, 400, 800, 1000, 1500 grits on both of them. It was crazy how warped my heatsink was and my Q6600 was a mountain range with a surrounding...
- DaPoets
- Post #26
- Sep 5, 2007
- Forum: Cases & Cooling

RESOURCES

Top Bottom