Recent content by ojrules

O
Asrock 4CoreDual-SATA2

Hey ive finally gto the remote for my surround sound, but am having a few troubles with the coaxil mobo jobby.... the left and right from speakers both work, but the centre and subwoofers dont EDIT: After testing with the realtek speaker tester jobby i only get 2 speakers.. however when...
- ojrules
- Post #1,107
- Mar 10, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

nah i dont think they could make it for 45nm processors, i think its a rather different architecture..
- ojrules
- Post #1,060
- Mar 6, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

ive done the same thing, move from a 3.7 to a 2.4... in 3d mark, the processor scores higher... however in crysis i think i might have lost a few fps..
- ojrules
- Post #1,041
- Mar 2, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

fsb for ram, or cpu?... o and ive found that i've changed absolutely nothing, everything is on auto, with flex disabled, and 266 still works..
- ojrules
- Post #1,040
- Mar 2, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

nope i dont have flexibility option enabled.. however tomoro i will check al the bios settings.... ive been through all the remotes in my house trying to find a remote that gives the right signal... with no sucess.. so its costing me a tenner to buy another remote which i;l probably loose again...
- ojrules
- Post #1,034
- Mar 1, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

hmm... good point :P.. i shall check.. i think i just changed the dram voltage to normal... however im not sure... i'l reboot and check sometime... well.... i wired the coaxil cable to a 2 pin plug, and have "plumbed it in" , however i cant find my remote to my surround sound system :P.. so i...
- ojrules
- Post #1,030
- Mar 1, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

Hey.... the settings you advised me a while ago didnt work... DRAM Frequency [333MHz (DDRII667) ] Flexibility Option [Disabled] DRAM CAS# Latency [5] DRAM Bank Interleave [4-Way] Precharge to Active (Trp) [5T] Active to Precharge (Tras) [18T] Active to CMD (Trcd) [5T] REF to...
- ojrules
- Post #1,028
- Mar 1, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

I tried these settings: 333mhz flexibility option enabled Dram voltage Normal however the frequency in cpuz is shown as 235mhz... on the other hand the motherboard has given me rather tigh timings, even though they were set to auto: Cas: 3 Ras-Cas 3 trp 3 tras 9 cr 2
- ojrules
- Post #1,026
- Feb 29, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

@Cpmee .. i dont completely folow you... so you attach the cable to gnd and the middle one, and then attatch it to a phono cable.. how?... o also when u advised about my ram timings, you advised that the voltage was set to low.. surely i should set it to normal?..
- ojrules
- Post #972
- Feb 22, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2
- ojrules
- Post #968
- Feb 21, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

off the topic how can you route the hdmi audio cable on the mobo to a coaxil output?..
- ojrules
- Post #966
- Feb 21, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

erm, no running at default stuff is working,.. just some initial teething problems... its that once at 2.4ghz i cant get stable decent mem speeds (other than auto).. meaning for instance in crysis it actualy plays slower, than before with my p4.... mypsu is fine; an enermax beast 620w, could run...
- ojrules
- Post #946
- Feb 15, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

Hey i've tired the settings with no sucess.... It just cold booted... Then i tied 533(?)(the middle one), with all other settings set to default , with no sucess... I then booted it with a previous stable clock of 2.40, but it crashed in windows.. I then ran it all at default (2.0ghz) and it...
- ojrules
- Post #942
- Feb 15, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

Will this enable me to raise cpu frequency aswell?..
- ojrules
- Post #925
- Feb 13, 2008
- Forum: Motherboards
O
Asrock 4CoreDual-SATA2

Ok, i'l keep the besl mod in mind..... I do have the second stick of ram, but after failing to second boot with 2 sticks in i reverted to 1 stick (however i didn't get to fiddle around with settings)... heres my ram http://www.overclockers.co.uk/...701&catid=8&subcat=144
- ojrules
- Post #916
- Feb 12, 2008
- Forum: Motherboards

RESOURCES

Top Bottom