Recent content by panoramarts

P
p35-ds4 rev 2.0

Yes thats true. I tried many different combinations but all failed mostly. I think its motherboard fault here for some reason. I took max CPU to 2.9mhz with multiplyer 8. Anyways i will give a shot at Qflash, i might get lucky. thanks for help cozumel. On the other hand I am disappointed at...
- panoramarts
- Post #52
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

Maybe its a PSU issue. I am running Antec true Power 2.0. I dont have so much load on it. PSU never gave me problems on AMD and DFI. OR its faulty board.
- panoramarts
- Post #49
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

BIOS Current Settings: (D: Disabled E: Enabled N:Normal Std= standard) C1E= D EIST= D TM2= E Perf Enhan= Std FSB= 400 PCIe= 100 SPD=2 DRAM= 6-6-6-24 DDR2 Volt= N PCIe= N FSBv=+0.1 CPU=1.3 Loadline=D Results: Post screen shows 267x9 (two times success on above settings showing...
- panoramarts
- Post #48
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

not using any expansion slots. Only graphics slot. I will try above setting. I am telling you I don't understand the computer behavior. I never experienced this on my AMD, clocking on DFI.
- panoramarts
- Post #47
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

BIOS Current Settings: (D: Disabled E: Enabled N:Normal Std= standard) C1E= D EIST= D TM2= E Perf Enhan= Std FSB= 300 PCIe= 100 SPD=2 DRAM= 6-6-6-24 DDR2 Volt= N PCIe= N FSBv=+0.1 CPU=1.28 Loadline=D Results: Boot failures. (two time success @ above settings). testing by...
- panoramarts
- Post #45
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

.
- panoramarts
- Post #43
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

BIOS Current Settings: (D: Disabled E: Enabled N:Normal Std= standard) C1E= D EIST= D TM2= E Perf Enhan= Std FSB= 333 PCIe= 100 SPD=2 (so as to run ddr @ 666) DRAM= 6-6-6-24 DDR2 Volt= N PCIe= N FSBv=+0.05 CPU=1.28 Loadline=D Results: Failed to post at above settings (only one...
- panoramarts
- Post #42
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

BIOS Current Settings: (D: Disabled E: Enabled N:Normal Std= standard) C1E= D EIST= D TM2= E Perf Enhan= Std FSB= 370 PCIe= 100 SPD=3 DRAM= 6-6-6-24 DDR2 Volt= N PCIe= N FSBv=+0.05 CPU=1.28 Loadline=D Results: Post screen shows 267x9. Passes post successfully. CPU-z shows 267x9...
- panoramarts
- Post #39
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

no "cotton-picki pesky" boot failures. Need some settings cozumel. Check your PM.
- panoramarts
- Post #36
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

no error so far in prime. CHECK PM
- panoramarts
- Post #35
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

Ok getting into windows testing under prime 25. (Round off checked) ------------------------------- max temp @ 46 C (core:3)
- panoramarts
- Post #33
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

i did all those too. I doubt that i have memory issues because i was able to run at 1170 or 585 or PC9630 on timing 5-5-5-15.
- panoramarts
- Post #31
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

OK did Advanced BIOS Features C1E = Disabled EIST = Disabled Init Display First = PEG (Please confirm that you have your 8800GTX in the first PCIe x16 slot (marked PCIE_16_1) Leave all other settings on this screen as defualt Aplied--> M.I.T. C.I.A.2 = Disabled Performance Enhance =...
- panoramarts
- Post #28
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

PCIe x16 is on second (below)
- panoramarts
- Post #27
- Jan 17, 2008
- Forum: Motherboards
P
p35-ds4 rev 2.0

I mostly updated bios through windows
- panoramarts
- Post #25
- Jan 17, 2008
- Forum: Motherboards

RESOURCES

Top Bottom