Recent content by Tuff

T
vey bad problem (HELP PLZ)

Simplest way would be to take the hard drive to another person...who HAS XP and get them to burn the info off. Have you updated the BIOS on your m/b to support greater than 32 gig? Aslo..check the jumpers on the Hard drive...some have jumpers that limit the drive to read just 32 gig. I have...
- Tuff
- Post #20
- Jul 16, 2003
- Forum: CPUs and Overclocking
T
The last of the great 1700+s, the DLT3C 0322XPMW

I run mine at 1.7 volts. Tuff
- Tuff
- Post #19
- Jul 13, 2003
- Forum: CPUs and Overclocking
T
The last of the great 1700+s, the DLT3C 0322XPMW

I have an 03/21 1800 Xp that does 2400mhz...and will post at 2500mhz. Maybe you all should be looking for 1800's??? Tuff
- Tuff
- Post #6
- Jul 12, 2003
- Forum: CPUs and Overclocking
T
how (much) to OC TB rev. B

I have tried the 83mhz on my Asus Nforce board...now its being sent to asus to get fixed. Tuff
- Tuff
- Post #11
- Jul 10, 2003
- Forum: CPUs and Overclocking
T
A small problem..I hope

Nope no go...I let it sit overnight to clear the Cmos and still will not boot. Tuff
- Tuff
- Post #9
- Jul 9, 2003
- Forum: CPUs and Overclocking
T
Just in: Barton 2500+ results by tonight.

I have contacted ASUS about the claim of the 400mhz...so far their advice has given me more problems. 'Tuff
- Tuff
- Post #10
- Jul 8, 2003
- Forum: CPUs and Overclocking
T
A small problem..I hope

I will let it sit longer and see what happens...also..I was aware of the loss of performance..but they said to try it. I guess they wanted to eliminate the RAM as the limiter for the fsb problem. 'Tuff
- Tuff
- Post #7
- Jul 8, 2003
- Forum: CPUs and Overclocking
T
A small problem..I hope

I followed the directions in the manual and have had NO success. Any other idea's? Tuff
- Tuff
- Post #5
- Jul 8, 2003
- Forum: CPUs and Overclocking
T
A small problem..I hope

I thought you could reset the Cmos with the start button and the End key??? I will try the other way :) Tuff
- Tuff
- Post #4
- Jul 8, 2003
- Forum: CPUs and Overclocking
T
A small problem..I hope

I got an email from Asus about my A7N8X 1.4 version motherboard. It was concerning the 200mhz front bus speed as my comp is not stable there. They told me to set my Memory to a slower speed than the 200 mhz...I assume they meant to set it at 83%. "async" They did not mention "Timings" I did...
- Tuff
- Thread
- Jul 8, 2003
- Replies: 8
- Forum: CPUs and Overclocking
T
Picked up an XP 1800+

Default voltage is 1.5 Tuff
- Tuff
- Post #4
- Jun 27, 2003
- Forum: CPUs and Overclocking
T
Picked up an XP 1800+

Stepping is JIUHB 0321 Runs @ 2300mhz 1.7 volts on water :) Might try for higher later. Tuff
- Tuff
- Thread
- Jun 27, 2003
- Replies: 3
- Forum: CPUs and Overclocking
T
Heatkiller, DangerDen, Cuplex or which water block?

The best blocks out there...bar none...are the WhiteWater and the MicroCup. Find one of these if you can. Tuff
- Tuff
- Post #5
- May 13, 2003
- Forum: Cases & Cooling
T
Watercooling: 2 Radiator question...

You failed to mention what type of waterblock you are using. Also...I would think that one Rad is enough...as I run 1 with a MicroCup Latest Technology in water blocks and I get 32 deg C. 34ish full load. I would be looking at getting a more efficient block first...then mess around with the...
- Tuff
- Post #2
- May 13, 2003
- Forum: CPUs and Overclocking
T
quick poll

Air IN through the bottom...out through the top. Tuff
- Tuff
- Post #2
- Apr 26, 2003
- Forum: Cases & Cooling

RESOURCES

Top Bottom