I Purchased a new system-P3-800EB 133FC-PGA and it came with a Superpower Motherboard.I thought I was getting an ASUS CUSL2-C M/B .
The only info I could find on this M/B came from a review made in Sept,1999.The website for Superpower is apparently defunct. But here are the M/B specs I found:
6XV-133 Motherboard
Manufacturer - Superpower
General
The 6XV-133 is a Single-CPU Slot 1 Based ATX mainboard With VIA PC-133 chipset.
Technical Specifications
CHIPSET:
VIA 693+596B (6XV-A66)
VIA PC-133 AGPset (6XV-133) Board Size:305*190mm(W*L) ATX
CPU:
Intel Pentium III (133MHz) 533 MHz~(6XV-133)
Intel Pentium III (100MHz) 450 MHz~
Intel Pentium II (100MHz) 350~450 MHz
Intel Pentium II (66MHz) 233~333 MHz
Intel Celeron 266~433 MHz
Voltage:Auto Setting
Slot:
AGPx1, PCIx5, ISAx2
MEMORY:
168pin*3 DIMM(max.1.2GB) (6XV-133)
168pin*3 DIMM(max.768MB) (6XV-A66)
Supports PC-100 SDRAM DIMM
Supports PC-133 SDRAM DIMM (6XV-133)
Support High-speed Virtual Channel SDRAM (6Xv-133)
________________________________________________________________The place I purchased this computer from told me this was as good a setup as would have been if I had gotten the ASUS CUSL2-C M/B but I saved $70 with this board.
I know little about computers but it seems to me this is not accurate.
Looking at those specs it appears that: 1.they had to use a converter card to use the P3-800 and the specs say board is capable of supporting a P3 to 533mhz. So how is this going tu run a 800mhz CPU unless its just "overclocked"?. Please help me understand. Is this a perfectly acceptable configuration or am I being screwed over by this outfit?.Many thanks.
The only info I could find on this M/B came from a review made in Sept,1999.The website for Superpower is apparently defunct. But here are the M/B specs I found:
6XV-133 Motherboard
Manufacturer - Superpower
General
The 6XV-133 is a Single-CPU Slot 1 Based ATX mainboard With VIA PC-133 chipset.
Technical Specifications
CHIPSET:
VIA 693+596B (6XV-A66)
VIA PC-133 AGPset (6XV-133) Board Size:305*190mm(W*L) ATX
CPU:
Intel Pentium III (133MHz) 533 MHz~(6XV-133)
Intel Pentium III (100MHz) 450 MHz~
Intel Pentium II (100MHz) 350~450 MHz
Intel Pentium II (66MHz) 233~333 MHz
Intel Celeron 266~433 MHz
Voltage:Auto Setting
Slot:
AGPx1, PCIx5, ISAx2
MEMORY:
168pin*3 DIMM(max.1.2GB) (6XV-133)
168pin*3 DIMM(max.768MB) (6XV-A66)
Supports PC-100 SDRAM DIMM
Supports PC-133 SDRAM DIMM (6XV-133)
Support High-speed Virtual Channel SDRAM (6Xv-133)
________________________________________________________________The place I purchased this computer from told me this was as good a setup as would have been if I had gotten the ASUS CUSL2-C M/B but I saved $70 with this board.
I know little about computers but it seems to me this is not accurate.
Looking at those specs it appears that: 1.they had to use a converter card to use the P3-800 and the specs say board is capable of supporting a P3 to 533mhz. So how is this going tu run a 800mhz CPU unless its just "overclocked"?. Please help me understand. Is this a perfectly acceptable configuration or am I being screwed over by this outfit?.Many thanks.